1. <li id="93kbi"><object id="93kbi"></object></li>

    <button id="93kbi"><object id="93kbi"></object></button>

    無錫市揚名電熱電器廠

    0510-85416868

    溫控器
    Product
    聯系我們Contact us
    咨詢熱線
    0510-85416868

    手機:18912366584

    電話:0510-85416868

    傳真:0510-85401718

    地址:無錫市梁溪區揚名高新技術產業園匯太路58號

    • 溫控器

    防爆溫控器與電伴熱帶配套使用后,可以控制管線溫度,且可以調整溫度設定值。Applied with heating cable, temperature controller can adjust temperature in response to practical need.
     

    1產品結構 Structure

     
    防爆溫控器 Temperature Controller   圖25
      
                                                                                 側面圖    圖26
     
                                                                                  底面圖    圖27
     

    2產品型號 Catalog Number

    圖28
    Maximum temperature: 120℃-150℃-200℃
    Explosion-proof temperature controller

    3主要技術指標 Technical Parameters(表11)

    型號
    Catalog number
    防爆等級
    Explosion-proof level
    工作電壓
    Working voltage
    工作電流
    Working
    current
    控溫精度
    Temperature control precision
    絕緣電阻
    Insulation resistance
    電氣強度
    Dielectric strength
    防護等級
    Protection level
    FWK120/200 ExedⅡBT4 380V/220V ≤15A ±2.5℃ ≥60MΩ 2000V/min IP54
     
    ? FWK120:控溫范圍Temperature control range(0~120℃)
    ? FWK200:控溫范圍Temperature control range(50~200℃)
     

    4單相溫控器安裝方法 Installation

    ?  相線接A,零線接N; 
    connecting phase line to A, neutral line to N
    ?  a和n用導線接到電源接線盒中,與電熱帶相接;
    a terminal and n terminal are connected to heating cable
    ?  溫控器的探頭接到管路上,用鋁膠帶貼在管道上;
    attaching the temperature probe to the surface of the pipe with aluminum adhesive tape
    ?  溫控器旋鈕調到您所需要維持的溫度上。
    adjust the button to the number of practical temperature
     

    5產品使用與維護 Application and Maintenance

    ? 打開接線盒蓋,擰下接線嘴,將進線和出線電纜穿過各自的接線口,上緊接線盒蓋。
    Open the cover of the kit, screw off the connection terminal; insert the line through each terminal.
    ? 按接線腔內的接線圖接好電纜,擰緊接線嘴,上緊接線盒蓋。
    Connect the lines as the diagram, tighten the terminal, and then tighten the cover with screws.
    ? 打開溫度調接盒外蓋,將溫度調整到所需控制溫度處,然后擰緊外蓋。
    Adjust the temperature according to the practice need.
    ? 用卡箍將溫控器底座固定在適當位置,并將溫控探頭緊貼在被測試溫度的部位。
    Install the temperature controller at the proper position; attach the probe closely to the vessel.
    ? 將引出線接到電源盒腔內,與腔內電伴熱帶相接,溫控器進線接入電源,檢查無誤后即可送電工作。
    Connect the leading-out line with heating cable, connect the temperature controller to the power. Check the connection, and then turn on the power to operate.
    ? 溫控探頭只能水平或豎直安裝,否則會出現溫度不穩定現象。
    Keep the probe vertical or horizontal, or temperature will be unstable.
    ? 接線盒如有變形,裂痕和損壞,應停止使用,更換新接線盒。
    If the kit was deformed, chapped, please change a new one.
    下一個:尾端盒
    真人作爱试看90分钟_国产高清不卡无码视频_强制连续潮喷高清无码_免费香蕉成视频在线观看

    1. <li id="93kbi"><object id="93kbi"></object></li>

      <button id="93kbi"><object id="93kbi"></object></button>